HOW TO ADD BIAS AMP 2 TO ABLETON FULL
HOW TO ADD BIAS AMP 2 TO ABLETON SERIES

Therefore, we always recommend you do the following: We recommend that you use cabinets of the same impedance when used together as different impedances can cause a mismatch which can damage your amplifier.Īttached are a few example diagrams showing multiple speakers being used in parallel.Īlthough there may be a fault with your amp it is worthwhile eliminating any other possible causes first. When using more than one speaker or speaker cabinet at the same time it is important that the impedance matches correctly. They will deliver less power if used with a cabinet 8-16 Ohm cabinet.

HOW TO ADD BIAS AMP 2 TO ABLETON FULL

It is worth noting that ID:Series amplifiers only deliver their full power output when used with a 4 Ohm cabinet. Therefore, you need to match your speaker cabinets accordingly. Due to this unique design, all amps with TVP should always be treated in the same way as a valve amplifier of the same power output. The ID:Series amplifiers use a solid-state power section with Blackstar’s patent-applied for TVP (True Valve Power) feature. Therefore, you should always use a speaker cabinet that has a power rating greater than the amplifier’s maximum power rating, not according to the DPR setting. This is because DPR lets you retain all the tone and dynamics of your ‘full volume’ sound at lower performance levels. The design of Blackstar’s DPR circuit means that the amplifier can produce peaks and transients up to and exceeding the maximum output power rating of the amplifier, even with DPR set to minimum (10%).

HOW TO ADD BIAS AMP 2 TO ABLETON SERIES

Using speakers safely with Series One’s DPR control Ideally the speakers should be rated at least one and a half times higher than the amp output.ģ0 Watt amplifier – 45 Watt speaker power handling.ġ00 Watt amplifier – 150 Watt speaker power handling. You should always use a speaker cabinet that is of the correct impedance and has a higher power rating than your amplifier, or you risk damaging the amplifier and the speaker cabinet.Īs valve amps can produce peaks in their power output that exceed their power rating, we recommend that the speaker cabinet must be able to handle a higher output power than the rating of the amplifier.

ISF and ‘the sound in your head’ are only available on Blackstar products.

The ISF control is continuously variable between all the traditional responses allowing you to effectively design your own sound.

The tone controls remain fully interactive, just like in a regular tone stack.

ISF is a passive circuit giving a musical response that is not found in active parametric or ‘contour’ controls.

In this way you can design your own sound and truly find ‘the sound in your head’.

The ISF control allows you to infinitely adjust the response of the tone control network between any of the traditional voicings in a way that has never before been possible. Classic amplifier designs have their own versions of this network which leads to their own tonal voicings. Bass, Middle and Treble), is a key to the characteristic ‘voice’ of traditional guitar amplifiers. The conventional three way guitar EQ network, or tone stack (a.k.a. The Infinite Shape Feature (ISF) is a patented feature only available on Blackstar products. DPR’s dynamic power reduction is only available on Blackstar products.Unlike power attenuators, DPR places nothing between the output of the amplifier and the loudspeaker and hence as the power is reduced the feel, tone and reliability of the amplifier is maintained.sag) of a small overdriven valve amp, at any volume level. DPR is a ‘dynamic’ circuit, delivering the exact compression (a.k.a.DPR allows continuously variable power reduction, down to 10%, so you can use your valve amp in any playing situation.This is because at higher volume levels the output valves introduce musical distortion and compression which are a vital part of the valve amplifier experience.īlackstar’s patented DPR feature controls the output power level by dynamically adjusting the output stage voltages, allowing power valve distortion and compression at any volume level. It is well known that valve amplifiers sound best when they are turned up loud. Dynamic Power Reduction (DPR) is a patented feature only available on Blackstar products.

How to add bias amp 2 to ableton